SAF PROFESSIONAL
FAPR Polyurethane Foam-Adhesive professional
Application:
sealing adhesive foam is used for fastening heat-insulating plates indoors and outdoors, filling cavities and cracks including those around pipeline systems and cable routes as well as for sealing joints, sound and heat insulation of building structures and for installation purposes in industrial and household environments.
Recommendations for use: the application temperature of the cylinder should remain within 15…+30°C. Shake the cylinder for at least 1 minute before use. At temperatures above 0°C, slightly moisten dry surfaces. Apply with a gun/applicator in strips/dots with a diameter of no more than 1-2 cm. Wait 2-3 minutes, connect the surfaces to be glued and fix until complete setting.
Recommendations for use: the application temperature of the cylinder should remain within 15…+30°C. Shake the cylinder for at least 1 minute before use. At temperatures above 0°C, slightly moisten dry surfaces. Apply with a gun/applicator in strips/dots with a diameter of no more than 1-2 cm. Wait 2-3 minutes, connect the surfaces to be glued and fix until complete setting.
Super strong fixation
High temperature resistant
Indoor and outdoor
Soundproofing
Anti fungal
Waterproof
Paintable
Eco friendly
Lifetime
Euro quality
Application Method:
The foam is used under the temperatures from -10 to + 30 ° C and a relative humidity of no less than 60%. To achieve maximum output and optimal foam physical and mechanical properties, store the cylinder at room temperature for at least 24 hours, shake it for no less than 1 minute immediately before use to thoroughly mix the content, and apply the foam onto work surfaces free from dust, dirt, fat, ice and frost dew. At high temperatures, the surface should be moistened immediately before applying the foam. Working position of the cylinder is upside down. Apply the adhesive foam to the plates in stripes of about 1-1.5 cm in diameter around the perimeter at a distance of 3-5 cm from the edges, and then fill in the perimeter crosswise. Wait for 2-3 minutes, then attach the plate to the wall and fix it until it sets (approximately for 15-20 minutes). Shake the cylinder from time to time during work. Cured foam should be painted or plastered for protection from UV radiation damages.
The foam is not adhesive on plastic film, so before performing any works on the surface that should stay free from foam protect it with a film. Uncured foam can be washed off with a special cleaning liquid while hardened foam can be removed mechanically.
Safety Measures:
Keep away from children. Do not use near flames, hot surfaces or operating electrical equipment. When applying the foam, use personal protective equipment. In case of direct contact with skin or mucous membranes, uncured foam should be removed with a dry clean cloth and thoroughly rinsed with water. Then, seek medical help if necessary. Do not puncture/damage the cylinder even after use.
Storage Conditions:
Store in the original manufacturer's packaging with the valve up under the temperature from + 5 to + 30°C at a distance of at least 1.5 m from heaters and open flame sources, protected from moisture and direct sunlight. Do not heat above +50°C.
Shelf Life: - 18 months from the manufacture date.
The foam is used under the temperatures from -10 to + 30 ° C and a relative humidity of no less than 60%. To achieve maximum output and optimal foam physical and mechanical properties, store the cylinder at room temperature for at least 24 hours, shake it for no less than 1 minute immediately before use to thoroughly mix the content, and apply the foam onto work surfaces free from dust, dirt, fat, ice and frost dew. At high temperatures, the surface should be moistened immediately before applying the foam. Working position of the cylinder is upside down. Apply the adhesive foam to the plates in stripes of about 1-1.5 cm in diameter around the perimeter at a distance of 3-5 cm from the edges, and then fill in the perimeter crosswise. Wait for 2-3 minutes, then attach the plate to the wall and fix it until it sets (approximately for 15-20 minutes). Shake the cylinder from time to time during work. Cured foam should be painted or plastered for protection from UV radiation damages.
The foam is not adhesive on plastic film, so before performing any works on the surface that should stay free from foam protect it with a film. Uncured foam can be washed off with a special cleaning liquid while hardened foam can be removed mechanically.
Safety Measures:
Keep away from children. Do not use near flames, hot surfaces or operating electrical equipment. When applying the foam, use personal protective equipment. In case of direct contact with skin or mucous membranes, uncured foam should be removed with a dry clean cloth and thoroughly rinsed with water. Then, seek medical help if necessary. Do not puncture/damage the cylinder even after use.
Storage Conditions:
Store in the original manufacturer's packaging with the valve up under the temperature from + 5 to + 30°C at a distance of at least 1.5 m from heaters and open flame sources, protected from moisture and direct sunlight. Do not heat above +50°C.
Shelf Life: - 18 months from the manufacture date.
Category: PU Foam